rsg electronic components gmbh ?sprendlinger ldst. 115 ? 63069 offenbach ?+49 69-984047-0 ?rsg-electronic.de page 1 (5) stand juni 2016 rev 01 dc/dc-converter rs1/rd1-s05 0.5w unregulated single output we energize electronics! an acal group company we energize electronics! ? 4 pin sil/ 8pin dil package ? 1000vdc isolaton ? up to 3000vdc isolaton ? low ripple and noise ? efciency up to 83% ? operatng temperature range: -40 ~ +85c ? non conductve black plastc case ? emi complies with en55022 class b output specification voltage accuracy: 3% line regulaton: 1.2% (per 1%vin change) load regulation: 10% ( from 20 to 100%) load output 3.3v model: 20% ripple noise (20mhz bandwidth): 100mv pk-pk temperature coefcient: 0.02% c capacitor load: see table input specifications voltage range: 10% max. input current: see table no-load/full-load input current: see table input filter: capacitors input refected ripple current : 20ma pk-pk general specifications efciency: see table i/o isolaton voltage (60sec): 1000 ~ 3000vdc i/o isolaton capacitance: 60pf typ. i/o isolaton resistance: 1000m ohm switching frequency: variable 80khz humidity: 95% rel h reliability calculated mtbf : >1.121mhrs (mil-hdbk-217 f) safety standard: (designed to meet): iec 60950-1 1) these are stress ratngs. exposure of devices to any of these conditons may adversely afect long-term reliability. 2) (1.5mm from case 10sec max.) 3) all specifcatons typical at ta= 25c, nominal input voltage and full load unless otherwise specifed. 4) the informaton and specifcaton contained in this data sheet are believed to be correct at tme of publicaton. however rsg accepts no responsibility for consequences arising from printng errors or inaccuracies. specifcatons are subject to change without notce. environmental specification operatng temperature range: -40c ~+85c (see deratng curve) maximum case temperature: 100c storage temperature : -40c ~+125c cooling : nature convecton physical specifications: case material: non-conductve black plastc (ul94v-0 rated) pin material sip case: ? 0.5mm alloy42 solder-coated pin material dip case: ? 0.5mm brass solder-coated potng material: epoxy (ul94v-0 rated) weight case- sip: 1.5g weight case-dip: 1.8g dimmension sip: 0.46 x 0.24 x 0.40 dimmension dip: 0.50 x 0.40 x 0.27 absolute maximum ratings (1) input surge voltage (100ms)/ 3.3v models: 6vdc max 5 v models: 7vdc max 12v models: 15vdc max 15v models: 18vdc max 24v models: 28vdc max 48v models: 54vdc max soldering temperature (2) : 260c max. emc specifications radiated-/conducted emissions: en55022 class b esd: iec 61000-4-2 perf.criteria a rs: iec 61000-4-3 perf.criteria a eft: iec 61000-4-4 perf.criteria a surge: iec 61000-4-5 perf.criteria a cs: iec 61000-4-6 perf.criteria a pfmf iec 61000-4-8 perf.criteria a
rsg electronic components gmbh ?sprendlinger ldst. 115 ? 63069 offenbach ?+49 69-984047-0 ?rsg-electronic.de page 2 (5) stand juni 2016 rev 01 rd1 - xx xx x xx power (w) input 03=3.3v t ype a x code inter nal isolation (kvdc) 48=48v 20= 2.0 48=48v rd1 - xx xx x xx power (w) input 03=3.3v t ype a x code inter nal isolation (kvdc) e?ae? s 20= 2.0 48=48v model selection guide model number input input current output output current voltage range (vdc) no - load (ma) full load (ma) voltage (vdc) full load (ma) efficiency @fl(%) capacitor load(uf) rs1 - 0303s05 ax 3. 3 20 205 3.3 152 76 100 rs1 - 0305s05 ax 3. 3 25 216 5 100 70 100 rs1 - 0307 s05 ax 3. 3 25 216 7.2 69 70 100 rs1 - 0309s05 ax 3. 3 25 216 9 56 70 100 rs1 - 0312s05 ax 3. 3 25 201 12 42 72 100 rs1 - 0315s05 ax 3. 3 25 208 15 33 73 100 rs1 - 0318s05 ax 3. 3 25 208 18 28 73 100 rs1 - 0324 s05 ax 3. 3 25 208 24 21 73 100 rs1 - 0503 s05 ax 5 20 132 3.3 151.5 76 100 rs1 - 0505s05 ax 5 13 121 5 100 83 100 rs1 - 0507s05 ax 5 15 134 7.2 69.44 75 100 rs1 - 0509 s05 ax 5 15 128 9 55.55 78 100 rs1 - 0512 s05 ax 5 18 127 12 41.67 79 100 rs1 - 0515 s05 ax 5 22 130 15 33.33 77 100 rs1 - 0518s05 ax 5 20 127 18 27.77 79 100 rs1 - 0524 s05 ax 5 25 134 24 20.83 75 100 rs1 - 1203 s05 ax 12 15 58 3.3 151.5 72 100 rs1 - 1205 s05 ax 12 10 54 5 100 78 100 rs1 - 1207 s05 ax 12 15 57 7.2 69.44 73 100 rs1 - 1209 s05 ax 12 15 57 9 55.56 73 100 rs1 - 1212s05 ax 12 20 58 12 41.67 72 100 rs1 - 1215 s05 ax 12 20 61 15 33.33 69 100 rs1 - 1218s05 ax 12 15 61 18 27.77 68 100 rs1 - 1224 s05 ax 12 15 59 24 20.83 71 100 rs1 - 1503s05 ax 15 10 44 3.3 151.5 75 100 rs1 - 1505s05 ax 15 8 43 5 100 78 100 rs1 - 1507s05 ax 15 12 44 7.2 69.44 75 100 rs1 - 1509 s05 ax 15 12 44 9 55.55 75 100 rs1 - 1512 s05 ax 15 10 44 12 41.67 77 100 rs1 - 1515s05 ax 15 15 48 15 33.33 70 100 rs1 - 1518s05 ax 15 12 51 18 27.77 66 100 rs1 - 1524 s05 ax 15 10 51 24 20.83 66 100 rs1 - 2403s05 ax 24 8 31 3.3 151.5 69 100 rs1 - 24 05 s05 ax 24 8 29 5 100 73 100 rs1 - 2407s05 ax 24 10 30 7.2 69.44 70 100 rs1 - 2409 s05 ax 24 10 30 9 55.55 71 100 rs1 - 2412 s05 ax 24 8 30 12 41.67 71 100 rs1 - 2415s05 ax 24 10 29 15 33.33 73 100 rs1 - 2418s05 ax 24 10 29 18 27.77 73 100 rs1 - 2424 s05 ax 24 10 29 24 20.83 72 100 rs1 - 4803 s05 ax 48 6 17 3.3 151.5 60 100 rs1 - 485 s05 ax 48 6 16 5 100 66 100 rs1 - 4807s05 ax 48 6 17 7.2 69.44 60 100 rs1 - 4809s05 ax 48 6 17 9 55.55 62 100 rs1 - 4812s05 ax 48 6 17 12 41.67 64 100 rs1 - 4815 s05 ax 48 6 17 15 33.33 62 100 rs1 - 4818s05 ax 48 6 17 18 27.77 62 100 rs1 - 4824 s05 ax 48 10 18 24 20.83 61 100 s uffix ?3? means 3 kvdc isolation dc/dc-converter /d- nrete ne tt we energize electronics! an acal group company we energize electronics! sufx 3 means 3kvdc isolaton
rsg electronic components gmbh ?sprendlinger ldst. 115 ? 63069 offenbach ?+49 69-984047-0 ?rsg-electronic.de page 3 (5) stand juni 2016 rev 01 model selection guide model number input input current output output current dc/dc-converter /d- nrete ne tt we energize electronics! an acal group company we energize electronics! sufx 3 means 3kvdc isolaton
rsg electronic components gmbh ?sprendlinger ldst. 115 ? 63069 offenbach ?+49 69-984047-0 ?rsg-electronic.de page 4 (5) stand juni 2016 rev 01 +vout +v in dc/dc converter - vin - vout +vout +vin dc /dc converter - vin - vout c3 input reflected ripple current test step input reflected ripple current is measured through a source inductor lin(12uh) and a source capacitor cin(47uf, esr<1.0? at 100khz) at nominal input and full load. l in current probe cin load output ripple & noise measurement test the scope measurement bandwidth is 20mhz . load emi filter input filter components (c1 , l , c2 , c3) are used to help meet conducted emissions requirement for the module. these components should be mounted as close as possible to the module; and all leads should be minimized to decrease radiated noise. l load c1 c2 +vout dc/dc converter - vout scope c1 l c2 c3 r s 1 /rd1-0 3 xxs05ax 1210, 2. 2uf/100v 18uh r s 1/rd1-05 xxs05ax 1210, 2.2uf/100v 18uh r s 1/rd1-1 2xxs05ax 1210, 2.2uf/100v 18uh r s 1/rd1-1 5xxs05ax 1210, 2.2uf/100v 18uh r s 1/rd1-2 4xxs05ax 1210, 2.2uf/100v 18uh 1210, 2.2uf/100v 1206, 470pf/2kv r s 1/rd1-4 8xxs05ax electrolytic capacitor, 10uf/100v 18uh 1210, 2.2uf/100v 1206, 470pf/2kv the models listed above is just for standard type. if you need the special specification product, please contact our service member by telephone presented in shortform cover or e- mail t o : info@rsg - electronic.de 1. ripple/noise measured with 20mhz bandwidth. 2. tested by minimal vin and constant resistive load. 3. measured input reflected ripple current with a simulated source inductance of 12uh. 4. exceeding the absolute ratings of the unit could cause damage. it is not allowed for continuous operating. 5. operation under no - load conditions will not damage these devices, however they may not meet all listed specifications. 6. input filter components are be required to help meet conducted emission class b, which application refer to the emi filter of design & feature configuration. 7. an external filter capacitor is required if the module has to meet iec61000 -4-4 and iec61000 -4- 5. the filter capacitor rsg suggest: nippon - chemi - con ky series, 470uf/100v. +vout +v in dc/dc converter - vin - vout +vout +vin dc /dc converter - vin - vout c3 input reflected ripple current test step input reflected ripple current is measured through a source inductor lin(12uh) and a source capacitor cin(47uf, esr<1.0? at 100khz) at nominal input and full load. l in current probe cin load output ripple & noise measurement test the scope measurement bandwidth is 20mhz . load emi filter input filter components (c1 , l , c2 , c3) are used to help meet conducted emissions requirement for the module. these components should be mounted as close as possible to the module; and all leads should be minimized to decrease radiated noise. l load c1 c2 +vout dc/dc converter - vout scope c1 l c2 c3 r s 1 /rd1-0 3 xxs05ax 1210, 2. 2uf/100v 18uh r s 1/rd1-05 xxs05ax 1210, 2.2uf/100v 18uh r s 1/rd1-1 2xxs05ax 1210, 2.2uf/100v 18uh r s 1/rd1-1 5xxs05ax 1210, 2.2uf/100v 18uh r s 1/rd1-2 4xxs05ax 1210, 2.2uf/100v 18uh 1210, 2.2uf/100v 1206, 470pf/2kv r s 1/rd1-4 8xxs05ax electrolytic capacitor, 10uf/100v 18uh 1210, 2.2uf/100v 1206, 470pf/2kv the models listed above is just for standard type. if you need the special specification product, please contact our service member by telephone presented in shortform cover or e- mail t o : info@rsg - electronic.de 1. ripple/noise measured with 20mhz bandwidth. 2. tested by minimal vin and constant resistive load. 3. measured input reflected ripple current with a simulated source inductance of 12uh. 4. exceeding the absolute ratings of the unit could cause damage. it is not allowed for continuous operating. 5. operation under no - load conditions will not damage these devices, however they may not meet all listed specifications. 6. input filter components are be required to help meet conducted emission class b, which application refer to the emi filter of design & feature configuration. 7. an external filter capacitor is required if the module has to meet iec61000 -4-4 and iec61000 -4- 5. the filter capacitor rsg suggest: nippon - chemi - con ky series, 470uf/100v. +vout +v in dc/dc converter - vin - vout +vout +vin dc /dc converter - vin - vout c3 input reflected ripple current test step input reflected ripple current is measured through a source inductor lin(12uh) and a source capacitor cin(47uf, esr<1.0? at 100khz) at nominal input and full load. l in current probe cin load output ripple & noise measurement test the scope measurement bandwidth is 20mhz . load emi filter input filter components (c1 , l , c2 , c3) are used to help meet conducted emissions requirement for the module. these components should be mounted as close as possible to the module; and all leads should be minimized to decrease radiated noise. l load c1 c2 +vout dc/dc converter - vout scope c1 l c2 c3 r s 1 /rd1-0 3 xxs05ax 1210, 2. 2uf/100v 18uh r s 1/rd1-05 xxs05ax 1210, 2.2uf/100v 18uh r s 1/rd1-1 2xxs05ax 1210, 2.2uf/100v 18uh r s 1/rd1-1 5xxs05ax 1210, 2.2uf/100v 18uh r s 1/rd1-2 4xxs05ax 1210, 2.2uf/100v 18uh 1210, 2.2uf/100v 1206, 470pf/2kv r s 1/rd1-4 8xxs05ax electrolytic capacitor, 10uf/100v 18uh 1210, 2.2uf/100v 1206, 470pf/2kv the models listed above is just for standard type. if you need the special specification product, please contact our service member by telephone presented in shortform cover or e- mail t o : info@rsg - electronic.de 1. ripple/noise measured with 20mhz bandwidth. 2. tested by minimal vin and constant resistive load. 3. measured input reflected ripple current with a simulated source inductance of 12uh. 4. exceeding the absolute ratings of the unit could cause damage. it is not allowed for continuous operating. 5. operation under no - load conditions will not damage these devices, however they may not meet all listed specifications. 6. input filter components are be required to help meet conducted emission class b, which application refer to the emi filter of design & feature configuration. 7. an external filter capacitor is required if the module has to meet iec61000 -4-4 and iec61000 -4- 5. the filter capacitor rsg suggest: nippon - chemi - con ky series, 470uf/100v. dc/dc-converter /d- nrete ne tt we energize electronics! an acal group company we energize electronics!
rsg electronic components gmbh ?sprendlinger ldst. 115 ? 63069 offenbach ?+49 69-984047-0 ?rsg-electronic.de page 5 (5) stand juni 2016 rev 01 rs1-xxxxs05a1 rd1-xxxxs05a1 rs1-xxxxs05a1 rd1-xxxxs05a1 rs1-xxxxs05a1 rd1-xxxxs05a1 dc/dc-converter rs1/rd1-s05 0.5w unregulated single output we energize electronics! an acal group company we energize electronics! 8 pin dil 4 pin sil the models listed here are just standard type. if you need a product with special specifcaton or you have questons regarding packing standards (tube oder tape/reel) as well as applicaton support, please contact our specialists: sales @ rsg-electronic.de or +49 69-984047-41/-28
|
